![]() Read these articles and think again about whether it might be better to disable UPnP2 (and UPnP) altogether:ĭan Goodin.If you have multiple LAN (or VLAN) interfaces, you can add them using additional listen-on commands. Now enable and configure UPnP2 for the default LAN:.If you have already set up upnp with the wizard, get onto the router and delete that first:.The example commands below assume theĮdgeRouter-4 defaults where eth0 is the WAN port, and eth1 is for the LAN. This is the basic procedure to follow for enabling UPnP2 on an EdgeRouter. These are the most useful articles from the UI Community that I found: UPnP Wizard, without ever mentioning EdgeOS's support for the newer (and preferred) UPnP2 protocol that I did eventually consult the official EdgeOS User Guide, butĪs usual the info there was woefully incomplete: basically content to provide a walk through of the router's Requiring me (and every other user) to wade into the Internet swamp of bad advice for answers. I was surprised that there wasn't a clearly written, up-to-date, guide among the official doc on ui.com, thus So enabling UPnP on my EdgeRouter-4 wasn't something I had on the roadmap, but when I ran into difficulty getting DLNA to work on the default VLAN, I thought it was worth looking into (never mind that, as I later learned, having UPnP turned on wasn't going make a bit of difference on my local network: another reason that mastering theory should always come before practice). I've never been a fan of autoconfiguation when it comes to punching holes through the firewall. Send all traffic through the VPN connection.Want to configure UPnP on EdgeRouter-4? Don't do it! IntroductionĪs a former sysadmin that once helped ride herd over around 1,000 servers, of which around 10% were Internet-facing, ![]() System Preferences > Network > VPN L2TP > Authentication Settings User Authentication: Ĥ. System Preferences > Network > VPN L2TP Configuration: Default Adjust the newly created L2TP over IPsec interface. System Preferences > Network > "+" Interface: VPNĢ. Add a VPN connection in the network settings. In this section, we are using an Apple macOS computer as the L2TP client.ġ. Settings > Network & Internet > Status > Change Adapter Options > L2TP Adapter properties Security > Allow these protocols > Microsoft CHAP Version 2 (MS-CHAP v2) macOS L2TP VPN Client Navigate to the Windows 10 Network connections to change the allowed security protocols. Type of sign-in info: User name and passwordĢ. Settings > Network & Internet > VPN > Add a VPN connection VPN Provider: Windows (built-in) In this section, we are using a Windows 10 machine as the L2TP client. Make sure to match the credentials on the client and server (EdgeRouter). The next step is to configure the L2TP VPN settings on the client(s). Set vpn l2tp remote-access outside-address Set vpn l2tp remote-access dns-servers server-2 Set vpn l2tp remote-access dns-servers server-1 Set vpn l2tp remote-access client-ip-pool stop 192.168.100.249 Set vpn l2tp remote-access client-ip-pool start 192.168.100.240 Set vpn l2tp remote-access authentication local-users username password Set vpn l2tp remote-access authentication mode local Set vpn l2tp remote-access ipsec-settings authentication pre-shared-secret Set vpn l2tp remote-access ipsec-settings authentication mode pre-shared-secret Set vpn ipsec ipsec-interfaces interface Set firewall name WAN_LOCAL rule 30 action accept NOTE:The show vpn remote-access and show vpn ipsec sa commands can be used to verify the VPN client sessions. Set firewall name WAN_LOCAL rule 60 protocol udp Set firewall name WAN_LOCAL rule 60 log disable Set firewall name WAN_LOCAL rule 60 ipsec match-ipsec Set firewall name WAN_LOCAL rule 60 destination port 1701 ![]() Set firewall name WAN_LOCAL rule 60 description l2tp Set firewall name WAN_LOCAL rule 60 action accept Set firewall name WAN_LOCAL rule 50 protocol udp Set firewall name WAN_LOCAL rule 50 log disable Set firewall name WAN_LOCAL rule 50 destination port 4500 Set firewall name WAN_LOCAL rule 50 description nat-t Set firewall name WAN_LOCAL rule 50 action accept Set firewall name WAN_LOCAL rule 40 protocol esp Set firewall name WAN_LOCAL rule 40 log disable Set firewall name WAN_LOCAL rule 40 description esp Set firewall name WAN_LOCAL rule 40 action accept Set firewall name WAN_LOCAL rule 30 protocol udp Set firewall name WAN_LOCAL rule 30 log disable Set firewall name WAN_LOCAL rule 30 destination port 500 Set firewall name WAN_LOCAL rule 30 description ike ![]() set firewall name WAN_LOCAL rule 30 action accept Add firewall rules for the L2TP traffic to the local firewall policy. You can do this using the CLI button in the Web UI or by using a program such as PuTTY.Ģ. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |